| View previous topic :: View next topic |
| Author |
Message |
karimbxl
Nou Venit
Joined: 25 Dec 2006
Posts: 2
Location: Belgium
|
|
| Back to top |
|
 |
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
 Posted: Mon Dec 25, 2006 5:13 pm Post subject: |
 |
|
Nice pictures, thanks.
_________________
Victor Voinea
ALLservice HQ, Romania. |
|
| Back to top |
|
|
c0rtex
Nou Venit
Joined: 20 Jul 2008
Posts: 4
|
| Posted: Sun Jul 20, 2008 10:59 pm Post subject: |
|
|
Hi ! I successfully built the simple programmer device. Disassembled my x40 and now looking at this guys pics and wondering where pin 1 is on this chip. I do not want to connect the wires to the wrong pins.
Could someone please point out where GND SCL and SDA on this chip is ?
Thanks for your help !
 |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
|
| Back to top |
|
|
c0rtex
Nou Venit
Joined: 20 Jul 2008
Posts: 4
|
| Posted: Mon Jul 21, 2008 3:00 pm Post subject: |
|
|
Ok i can see where they go on the picture your added. The problem is that i can not see the writing nor the dot on pin 1 on my chip.
Is there any way you could tell me where the right pins are ?
Thx again |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
| Posted: Mon Jul 21, 2008 3:07 pm Post subject: |
|
|
The quick way is to check the Vcc=3.3V on the pin#8. From your perspective there are 2 possible pins, one is the Vcc and the other is the GND.
_________________
Victor Voinea
ALLservice HQ, Romania.
Last edited by victor on Mon Jul 21, 2008 3:13 pm; edited 1 time in total |
|
| Back to top |
|
|
c0rtex
Nou Venit
Joined: 20 Jul 2008
Posts: 4
|
| Posted: Mon Jul 21, 2008 3:12 pm Post subject: |
|
|
| Meaning taking a volt meter and holding it on each of the pins, one of them should show 3.3V as VCC even if the motherboard is not connected to anything ? |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
| Posted: Tue Jul 22, 2008 2:25 pm Post subject: |
|
|
I had 10 minutes to spend this morning, here you go:
Good luck!
_________________
Victor Voinea
ALLservice HQ, Romania. |
|
| Back to top |
|
|
c0rtex
Nou Venit
Joined: 20 Jul 2008
Posts: 4
|
| Posted: Tue Jul 22, 2008 4:12 pm Post subject: |
|
|
Thanks Victor ! You are a star. Was thinking of going out to get a Digital Multimeter tonight but you already did the job for me.
I`ll solder the wires on tonight and give the procedure a go. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
