| View previous topic :: View next topic |
| Author |
Message |
grubbi44
Nou Venit
Joined: 22 Jun 2008
Posts: 6
|
 Posted: Thu Jun 26, 2008 1:55 am Post subject: next step |
 |
|
Hey,
i looked all the thinks u advised me to, but couldnīt solve the next probblem!
i don't know what is: 232-01, 232-I1 , TTL-I1 and so on!
in this picture, it is different labeling....so please help !!!
http://www.pictureupload.de/pictures/260608015405_MAX232N.jpg
and what is VCC and where is it going to, in the driven I2C-sheet (at the top)?
thx |
|
| Back to top |
|
 |
grubbi44
Nou Venit
Joined: 22 Jun 2008
Posts: 6
|
| Posted: Fri Jun 27, 2008 11:23 pm Post subject: |
|
|
so no one here an idea how to solve my problem?? please help!!
thx in advance! |
|
| Back to top |
|
|
bob
S.F. Moderator
Joined: 07 Mar 2004
Posts: 802
Location: Staff
|
| Posted: Sat Jun 28, 2008 2:26 am Post subject: |
|
|
No ofense, but you seem to have zero experience (electronics) and we can't really teach you here.
But that's ok, nobody can do all so better take this to a local service shop or at least have a friend to do it for you. |
|
| Back to top |
|
|
grubbi44
Nou Venit
Joined: 22 Jun 2008
Posts: 6
|
| Posted: Sat Jun 28, 2008 9:44 am Post subject: |
|
|
so i only have little experience ... but if you could tell me the meaning, it would be enough information for me to build it.
that would be so great!
thx, grub |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
| Posted: Sun Jun 29, 2008 10:31 pm Post subject: |
|
|
The pins notation is not important. MAX232N and all other 232s have the same pin diagram. Don't bother with the names and take the pin number as reference.
Vcc=Vdc aka continuous current/direct current (+) pole
Good luck!
_________________
Victor Voinea
ALLservice HQ, Romania. |
|
| Back to top |
|
|
grubbi44
Nou Venit
Joined: 22 Jun 2008
Posts: 6
|
| Posted: Wed Aug 20, 2008 10:58 am Post subject: |
|
|
THANK YOU VICTOR!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I DID IT!
The Problem was that the contact to my needles was not given - so i was not able to read the bios! moreover i can give the advice to everyone that the given voltage always must be between GROUND and significant point. it was not clear for me in the beginning.
The Bios was TCPA locked, so sended the file to victor and flashed the new one! Very good and fast service!!
Nice Work!!
Keep it on......
Grubi |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
| Posted: Thu Aug 21, 2008 5:15 pm Post subject: |
|
|
Thanks for using our service, you're too kind
All the best
_________________
Victor Voinea
ALLservice HQ, Romania. |
|
| Back to top |
|
|
Ender
Nou Venit
Joined: 11 Nov 2008
Posts: 1
|
| Posted: Tue Nov 11, 2008 8:22 pm Post subject: T61 24S08 Pin Layout |
|
|
Victor,
Thank you for all the wonderful resources and information you have posted on your site! It has been extremely helpful is trying to recover my T61.
My question pertains to the P24S08 pin layout on the board. Both sides of the pin have no indentation or markings to indicate where the first pins starts. The board layout is the same as the T61-Alt.jpg.
very best,
Ender |
|
| Back to top |
|
|
victor
S.F. Boss
Joined: 07 Mar 2004
Posts: 2581
Location: Staff
|
| Posted: Tue Nov 11, 2008 10:53 pm Post subject: |
|
|
| Code: | 8 7 6 5
| | | |
P24S08
| | | |
1 2 3 4 |
Pin 1 is left-lower corner as you watch the P24S08 marks
_________________
Victor Voinea
ALLservice HQ, Romania. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
