ALLservice Service Forum
support board, PC repair, unlocking solutions
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

(T400,A30) Reader - "eeprom not available" all the

 
Post new topic   This topic is locked: you cannot edit posts or make replies.    Service Forum Forum Index -> IBM/Lenovo ThinkPad Password Help Center (EN)
View previous topic :: View next topic  
Author Message
Gregor
Nou Venit


Joined: 09 Jan 2010
Posts: 3
PostPosted: Sat Jan 09, 2010 12:12 pm    Post subject: (T400,A30) Reader - "eeprom not available" all the Reply with quote
Hello .

I´m trying to recover T400 using driven max232 reader. First try no luck getting eeprom not available. Unsolder, resolder again, again same error.
And again...and the same.
So Second T400, exactly same situation.
Finally I have tried with A30, and again no luck at all.

I´m sure soldering is fine, I have tried soldering, with needles as well and nothing happened. tester shows 1 on both fields. Cables are OK. Sometime on very beginning I dumped file 1kb lenght but filled only with 00 (zeros).
Then no luck at all. Just to confirm I have tried with USB to Serial (prolific) and dump started in 5th try or so, but with errors. With normal COM (tried on laptop and desktop PC) I´m always getting eeprom not available. Any help highly appreciated.

http://image-upload.de/image/Ff5Kyj/5996a430f3.jpg
http://image-upload.de/image/iao3Jw/cb3f3e990a.jpg
http://image-upload.de/image/yJ3Xi7/5beeb61194.jpg
http://image-upload.de/image/yq32Pt/c6e460b8d7.jpg

Last edited by Gregor on Sat Jan 09, 2010 2:05 pm; edited 1 time in total
Back to top
View user's profile Send private message
victor
S.F. Boss


Joined: 07 Mar 2004
Posts: 2581
Location: Staff
PostPosted: Sat Jan 09, 2010 2:02 pm    Post subject: Reply with quote
USB2COM - nope, must be a real COM port.

I see there some chinese copy, I am afraid our software does not support that, sorry. You must use an interface based on diagrams that comes with R24RF08 or buy an original ready made from us.
_________________
Victor Voinea
ALLservice HQ, Romania.
Back to top
View user's profile Send private message
Gregor
Nou Venit


Joined: 09 Jan 2010
Posts: 3
PostPosted: Sat Jan 09, 2010 2:03 pm    Post subject: Reply with quote
USB2COM just to try.
It´s not chinese copy, and developer is informing to use your software with his interface, so should work.
Back to top
View user's profile Send private message
victor
S.F. Boss


Joined: 07 Mar 2004
Posts: 2581
Location: Staff
PostPosted: Sat Jan 09, 2010 2:05 pm    Post subject: Reply with quote
It is a chinese copy, and we are aware of that. We only support our interfaces with the software.

I am sorry.
_________________
Victor Voinea
ALLservice HQ, Romania.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   This topic is locked: you cannot edit posts or make replies.    Service Forum Forum Index -> IBM/Lenovo ThinkPad Password Help Center (EN) All times are GMT + 2 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Powered by phpBB © 2001, 2005 phpBB Group